Understanding Plumber's Essentials When Installing a Bathtub
Understanding Plumber's Essentials When Installing a Bathtub
Blog Article
What are your beliefs on How to Install a Bathtub?
Setting up a bath tub isn't specifically brain surgery, yet it does call for solid plumbing, carpentry, and often, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably challenging job. If the old bathtub is readily accessible, the project can move quickly; if you need to open up a wall to get rid of the old bathtub as well as position the new tub, the task is much harder. In either case, the job is within a residence handyman's abilities, although you will require an assistant to vacate the old bathtub and embeded in the brand-new one. Ensure you have qualified yourself for the job as well as fit trying it. As opposed to employing a contractor to take over a halfway-completed project, it is far better to think about using one prior to you start. Chances are you may require a specialist plumber to make tube links.
This article will assist you install a brand-new bath tub in your restroom if you have actually already purchased a new bathtub and do not require to alter the plan of your previous water system pipes.
Your devices as well as material list need to make up the following:
Planning for the Setup
First of all, the supporting framework provided with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to stop strain on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be quite troublesome because of the limited gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the staying water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from turning during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old securing substance.
Before going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, put the bathtub in the called for position. The wooden boards are helpful in equally spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and changing the feet on the tub until the spirit level reads level.
To mount faucets, fit the bottom of the furthest versatile faucet port to the proper supply pipe by making a compression join; then do the same for the various other tap.
Turn on the supply of water as well as check all joints and new pipework for leakages and tighten them if essential. Fill the bathtub and additionally inspect the overflow electrical outlet and the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the bathtub must wait till the tub has actually been made use of at the very least once as this will settle it right into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making certain that the washing machines remain in area between the tap as well as the sink. Protect the faucet in position with the manufacturer provided backnut. Once the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet ports. The previous kind needs to be linked to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a stiff seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes and cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water prior to securing, to enable the activity experienced when the bathtub is in use. The sealant can break relatively very early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly available on the marketplace. It is recommended to fit the floor tiles using water-resistant or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very fascinated with A Step-by-Step Guide to Installing a Bathtub and I'm hoping you enjoyed reading my blog post. So long as you appreciated our blog entry if you please make sure you remember to share it. We thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.
About Report this page